Moji-Moji Design

Original Amigurumi Crochet Patterns


4 Comments

Tiny Toadstools

Looking through my sketchbooks and perusing my to-do lists I came to the conclusion it was about time I got organised and wrote up the free toadstool pattern that I’ve been meaning to do for a while now (I see a February date in the notebook and it is May already!). I’ve got way too many scribbled down ideas just waiting to blossom into fully formed patterns so here’s to having one less unfinished project left to worry about!

These Tiny Toadstools (or Mini Mushrooms if you prefer) measure approximately 2″ (5 cm) tall. They use only very small amounts of yarn and take about 30 minutes from start to finish so you can have your very own little crop of fungi in next to no time!

Materials:
Each toadstool requires approximately 1 gram each of Red and White 4 ply yarn plus 2 grams of polyester toy stuffing.

You’ll also need a 1.75 mm crochet hook, a pair of scissors, a yarn needle, stitch marker and a pair of tweezers (to help stuff the toadstool with).

*click here for a printable version of this pattern*

Pattern notes:
This pattern uses US sc (UK dc) throughout.

The invisible decrease (invdec) method is used throughout this pattern apart from on the back loop only crochet in Rnds 10 and 19 where the single crochet decrease (sc2tog) is used instead.

For stitch abbreviation meanings refer to the table at the end of the free pattern page. For those not familiar with invdec and sc2tog I’ve included photos below to show the difference.

Tie off and trim the colour change between the cap and the stalk on the inside of your work.

French knots are used to add the dots to the mushroom cap.

Toadstool Cap:

With Red yarn make 2 ch.
Rnd 1: 6 sc in second chain from hook. (6 sts)
Rnd 2: [Sc in next st, 2 sc in next st] 3 times. (9 sts)
Rnd 3: [Sc in each of next 2 st, 2 sc in next st] 3 times. (12 sts)
Rnd 4: [Sc in each of next 3 st, 2 sc in next st] 3 times. (15 sts)
Rnd 5: [Sc in each of next 4 st, 2 sc in next st] 3 times. (18 sts)
Rnd 6: [Sc in each of next 2 st, 2 sc in next st] 6 times. (24 sts)
Rnds 7-9: Sc in each st around. (3 rounds)

Toadstool Stalk:
(See pictures 1-9 below for details on sc2tog and invdec techniques)

Change to White yarn.
Rnd 10: Working in back loops only: [Sc in each of next 2 st, sc2tog] 6 times. (18 sts)
Rnd 11: [Sc in next st, invdec] 6 times. (12 sts)
Rnd 12: [Sc in each of next 2 st, invdec] 3 times. (9 sts)
Rnds 13-14: Sc in each st around. (2 rounds)
Rnd 15: [Sc in each of next 2 st, 2 sc in next st] 3 times. (12 sts)
Rnds 16-17: Sc in each st around. (2 rounds)
Rnd 18: [Sc in next st, 2 sc in next st] 6 times. (18 sts)
Rnd 19: Working in back loops only: [Sc in next st, sc2tog] 6 times. (12 sts)
Rnd 20: Invdec 6 times. (6 sts)

Fasten off, leaving a long yarn tail of approximately 27″ (70 cm) for finishing.

Single crochet 2 together (sc2tog) in back loops only (pictures 1-6)

Insert hook into next back loop, yarn over hook (1) and pull up a loop (2 loops on your hook) (2), insert hook into next back loop, yarn over hook (3) and pull up a loop (3 loops on your hook) (4), yarn over hook (5) and pull through all 3 loops on hook to complete the decrease (6).

Invisible decrease (invdec) (pictures 7-9)

Insert hook into front loops only of the next 2 stitches (3 loops on hook), yarn over hook (7), pull yarn through first 2 loops on hook (2 loops left on hook), yarn over hook (8), pull yarn through last 2 loops on hook to complete the decrease (9).

To Finish:

Your toadstool will lack a bit of shape at this point but don’t worry because we’re going to be remedying that in the next stages.

Use your tweezers to stuff the mushroom through the 6 stitch hole (10). Thread yarn tail onto yarn needle, pick up front loop only of remaining 6 stitches (11). Pull tight to close the hole and fasten with a small knot.

Insert the needle through the center of the base coming out where you want the first French Knot to be (12). Pull tightly on the yarn as you pull it through to flatten the bottom of the stalk.

Hold the yarn tight to keep the bottom flat and begin to make your first French knot by inserting the needle into the stitch space below and exiting where the needle first came out (13). Wrap the yarn 4 times around the needle (14), press onto the wrapped yarn with your thumb as you carefully pull the needle through to form the knot. Pull on the knot gently to neaten it (15).

Insert needle into stitch space at bottom of knot, coming out underneath the knot between Rnds 11 and 12 of toadstool (16-17). Insert needle 1 stitch away from last exit point, this time coming out where you want the second knot to be (18).

Pull on the yarn to begin forming the flat underside shaping of the gills (19). Keeping the tension on the yarn to maintain the shape, create your second French Knot in the same way as the first, finishing by coming out underneath the knot between Rnds 11 and 12 again (20). Continue in this way all around, pulling on the yarn as you go, until your mushroom has the desired shape. Once you are happy with the shape sew more French knots every few stitches (21) until you have the amount of spots you require.

Hide the yarn end inside the toadstool when you have finished.

I added a loop with some jewelry fixings and >Ta-dah!< I now have a really cute toadstool charm.

Looks pretty sweet dangling from my Instax Mini! Of course one toadstool leads to another…

…especially when you have such a gorgeous selection of Katia 10g amigurumi balls to play with.

Well, I just couldn’t resist, could you?!